Skip to main content

Posts

Showing posts from December, 2011

Message "096: Fatal Error 02" with Oki printers

096-02 error is a problem with the finisher. That's a "tray raise or lowering error". Solution 1: Check and clean the upper limit switch.  Solution 2: Replace the upper limet switch Solution 3: Check the shift motor operation and finisher control PCB board.  If the motor has failed, you need to replace it, and perhaps the control PCB too.

Error message Service Req E020 on Epson printers

This error could appears on these models: EPL-N3000, Aculaser C1100, Aculaser C1900... Solution 1 : “Secondary transfer voltage contact/release problem” Some electric parts can cause the trouble:  Transfer Roller Pressure Solenoid (SL2)  Transfer Roller Pressure Position Detection Sensor (PC7)  Engine Board (PWB-A)   Solution 2 : The problem come from the fuser. You have to replace it. EPL-N3000: C13S053017BA  Aculaser  C1100: 2090471 Aculaser C1900: 2077368

Error 61.05 on HP Designjet 500, 510, 800

Could appears on HP DesignJets 800 Series, DesignJet 500 and 510. Printer show a System Error: 61:05 The problem : That's an error Processing Job. This Error Code appears in these HP DesignJets with an HPGL/ 2 card installed, when processing either a PostScript or HP-GL/2 file. Solution 1 : Switch the Printer Off  Wait a few minutes.  Switch the Printer On  Resend the file that you were trying to print.  Solution 2 : If the Error Code reappears, try to generate the file again and try to print again.  If the file that is causing this error is PostScript, check if it is Binary. If the file is Binary, use AppleTalk to send the file to the Printer.  If AppleTalk is not being used to send the Binary file to the Printer, you have to change the PostScript settings to Binary through the Front Panel (Set-up menu / PS settings / Encoding / Binary).  Solution 3 : If the Error Code continues to reappear, check for a new release of the Driver: http://www8.hp.com/us/

How to reset drum counter on Oki B4400

Solution to reset the drum counter: Open the Status Monitor. Click "Printer Setup" then "Open Configuration" and "Maintenance". Click Drum Counter Reset. Click Apply. Click OK Réinitialiser le compteur du tambour Ouvir le Status Monitor. Cliquer sur "Printer Setup" puis "Open Configuration" et "Maintenance". Cliquer sur Drum Counter Reset (Réinitialiser le compteur du tambour). Cliquer Apply (appliquer). Cliquer sur OK Cero el contador del cilindro Abras Status Monitor. Clic en "Printer Setup" y "Open Configuration" y "Maintenance". Clic en Drum Counter Reset. Clic Apply (aplicar). Clic OK Reiniciar o contador do cilindro Lance o Status Monitor. Clique com "Printer Setup", "Open Configuration", "Maintenance". Clique com Drum Counter Reset. Clique Apply (aplicar). Clique OK Image Drum for Oki B4400 Printer

SSC Service Utility Software to reset Epson printers

SSC Service Utility allow to do many things with Epson printer : - Work directly with CSIC in Epson Stylus printers cartridges. - Reset or rewrite any chip using special addon device. - Freeze internal ink counters. - Reset internal ink counters even with empty cartridges. - Separate cleaning of color and black heads for all Epson inkjet printers, powerful cleaning mode. - Hot swapping of cartridges supported. - Resetting of protection counter. - More then 100 different Epson printers supported The site: http://www.ssclg.com/epsone.shtml Download the 4.30 version Printers you can reset with SSC utility : Epson Stylus Сolor 400/440/480 LPT/480SXU/580/600/640/660/670/680/777/740/760/ 800/850/860/880/900 / EM-900C/980/1160/1520/3000 C20 / C40 / CL-750/C41 / C42 / C43 / C44 / C45 / C46 / C47 / C48/C50/C60/C61 C62 /C63 / C64 /C65 / C66/C67 / C68 / D68/C70/C80/C82/C83 / C84/C85 / C86/C87 C88 / D88 and PE Photo RX420 / RX425 / RX430 /RX500 / RX510/RX520/RX600

Epson Stylus Photo R300 printer

Downloads : Drivers Manuals Cartridges : 7 Pack Compatible INK Cartridge for R300 Troubleshooting : Message on printer " some components have come to the end of their life ". You have to reset waste ink counter: Solution 1 : - Switch on the printer. - Hold on "STOP", "MAINTENANCE" and "POWER" buttons. - Release them when it's indicated. Solution 2 : Use the SSC Service Utility Software tou reset the product.

Brother MFC-425CN printer

Download : User's guide Cartridges : LC41BK: Black ink cartridge LC41C: Cyan ink cartridge   LC41M: Magenta ink cartridge   LC41Y: Yellow ink cartridge Brother Compatible LC41 8-Pack (2B/2C/2M/2Y) Troubleshooting: How to reset waste ink counter: Machine off Switch on the machine while holding down the “menu”button until all the leds are flashing on/off. Now you are in “maintenance” mode. press 80 press the “mono start” button several times until you see “purge: xxxx” press “2783” in order to reset the purge counter. You will see: “purge:0000” press “99” to exit the maintenance mode